![]() Went component by component and again, nothing. I even swapped out ALL of the cables, for ones still in packaging, nothing. Tried with 1 stick of each ram, tried with no ram, tried with no hard drives, still nothing. Reset the CMOS and removed the battery, nothing. Unplugging the GPU and tried the onboard video, with HDMI AND dvi, nothing. Now I also have an issue where my Corsair AIO, the block no longer lights up with its RGB either but everything is plugged in for that as well.Įverything inside the computer turns on, the Ram, all the fans, all the RGB, the videocard, literally everything except I can't get it to display video. I wanted to try to QBIOS but I don't know how I can do that when I can't even get the display to display. ![]() I've tried everything and nothing seems to work. When I swapped the parts I literally didnt unplug the ram or cpu, I just moved it straight over. The top left VRAM cooler that says AROUS on it usually lights up orange, but has no lights on it currently, it will flash when I plug in the powersupply and flip the power switch, but instantly turn off.Īlso there's no beeping on boot, and there's no lights or errors on the board. I also noticed that the reset button and holding the power button down no longer does anything for my computer, I can use the power button to turn it on but if I hold it it wont turn it off. I haven't gotten my 2070S or my 750W PSU yet, so those have not been included, all I did was move the internals over to the new case, and installed 3 new case fans for a total of 7 (3 on top for exhaust, 1 in back for exhaust, 2 on my AIO in the front for intake, and one below the AIO for intake.) the case came today and I moved all the internals over and now my computer wont post. I ordered the fracal meshify s2 as my computer case is really small and cramped and im upgrading to a bigger PSU and a 2070 super. So I'm 99% sure this is a Windows problem, not even a drivers problem.Last night I was playing on my pc just fine (Ryzen 5 3600, Gigabyte Arous Elite x570 mobo, gt 1070 GPU, 550W PSU, 16gb ram) Now, what is driving me mad, is that all of this works PERFECTLY on my second build, which has a gtx 1080. ![]() Reset the TV.- Reinstaled drivers (and deleting every monitor configuration through DDU).- Uninstalled every monitor through device manager. Test every f**** posible combo you can imagine connecting both monitors either by HDMI or DP to the GPU and even to the MOBO, Windows just won't work anymore with two monitors. ![]() Test if each monitor works individually with my pc, they both individually work on any of the ports either HDMI or DP (both monitors are hdmi only, but I have one conected through HDMI and one with a DP adapter). How do I fix this?ĭid you find any solution to this OP? I don't even know where to start to tell you how much I already tried with this, I -kind- of consider myself a tech savvy so I covered a lot of the basic stuff with no veil, what frustrates me a lot is that this wasn't happening till some days ago (didn't update driver at all, automatic updates are disabled).ģ080 ti, 3 DP, 1 HDMI.Mobo is a z370 with 1 HDMI, 1 DP.1 Samsung monitor.1 Samsung Smartv. I can't meet both goals because the connection/detection between my PC and the second monitor isn't working. To do so, all I need to do is have 2 HDMI cables to connect Switch -> capture card -> main monitor, then connect PC -> second monitor, right? My other goal is to connect the Switch console through my internal capture card (that has HDMI In and Out), display it on my main monitor, and still run the stream on the secondary monitor that is connected to the PC. My goal is to stream and use the 2nd monitor for controlling the stream, OBS and monitoring chat. Manual detection on PC doesn't detect anything.Īnd I know the second monitor and the HDMI cable works just fine, because I connected it to my Switch dock it worked and displayed the Switch just fine. Switching between HDMI and analog doesn't help, nor does any of the other menu settings. But it won't connect, it's either a black screen while it's on, or it shows ![]() I'm trying to use a Samsung B350 S27B350H 27-Inch LED Monitor as the second monitor in my PC setup. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |